Products - Pipe repair clamps Atlantik

Pipe repair clamps Atlantik are used for permanent reparation of broken and damaged pipes.

These allow quick and cost-effective interventions in steel, cast-iron, asbestos cement, PVC, PE pipes and other materials. They are produced for pipes of various diameters, from 1/2" to DN 1200 mm, available lengths are from 100 to 400 mm.

Pipe repair clamps are made out of stainless steel band (AISI 304 quality), in the thickness of 1 mm for the "Atlantik" clamps, and out of 0.8 mm sheet metal for the "Vektor" clamps. Both ends of the clamp are reinforced by a stainless steel sheet of the same quality, with the thickness of 3 mm. Clamp is fully lined on the inside face with a 7 mm rubber gasket. The used rubber has 60 shore hardness, and is molded for each dimension separately.

Interior of the rubber is molded - divided into the chambers in the form of square, each measuring 5x5 mm, with a depth of 2 mm, which ensures the good seal, even with oval tubes with uneven surface.

The rubber lining at the time of molding merges with a piece of stainless steel sheet, which comes on the junction of the repair clamp, so it would prevent the rubber distortion when tightening clamp, providing an effective seal all around the pipe.

Pipe repair clamps are used for reparation of the damaged pipes, without the need of cutting and re-insertion of a pipe part. They can also be used in case of fine cracks or joining the two ending parts of pipes. These elements allow angular misalignment up to 4° and axial deviation up to 3 mm. In addition, they can also be used for joining of pipes with different diameters, up to 2 mm, which ispreferred when joining asbestos pipes from different manufacturers.

The maximum working pressure of the repair clamps depends on the type of pipes, dimensions and condition of pipe work, clamp type (single clamp, double clamp, triple clamp, etc), the length of clamp, the type and size of the damage, as well as the conditions of servicing. In general, the allowable working pressure increases as the diameter decreases, so that the pipes up to DN 80 have working pressure of 25 bar, pipes up to DN 150 have pressure of 16 bar, and pipes over DN 175 can have pressure of 10 bar.

The advantages of using pipe repair clamps "Atlantik" are as follows:

These are the basic type of clamps produced for pipe diameters from 50 to 280 mm. Standard clamp's length is 200 mm, but they also come in lengths of 250, 300 and 400 mm. One-sided connection with 4 screws, provides faster and easier installation and lower price, compared to multi-part clamps for pipes of the same diameter.

The body of these clamps is made out two parts and enables two-sided connection, resulting in a higher resistance to the pressure. They are produced for pipe diameters from 80 to 600 mm, by the lengths of 200, 300 and 400 mm.

These clamps consist of a three-part body and have a three-way binding, which makes them very appropriate for high operating pressures (up to 25 bar). They are produced for pipe diameters from 250 to 800 mm. On customer's request, we also produce four-part and five-part clamps.

This type of repair clamp is designed for the reparation of high-pressure pipeline. The body of the clamp is reinforced at its ends and screws are made out of stronger material compared to standard clamps. These are available only as a multi-part clamps, with lengths of 200, 300 and 400 mm.

They can be used for minor reparation of the pipe work, produced solely as a one-piece fittings for pipe diameters from 22 to 90 mm. They are made out of stainless steel sheet metal of 1 mm thickness, with M10 bolts, and the length of 100 mm, this makes them stronger and more reliable than any other that can be found on the market.

Vektor clamp can be used as an economical alternative to the Atlantik single band clamp. They are produced for pipe diameters from 50 to 280 mm, and are available in 200, 250 and 300 mm lengths. They are suitable for working pressures up to 10 bar for diameters up to DN 150, and 6 bar for diameters up to DN 250.

These are more cost-effective alternative to Atlantik Mini clamps. They are produced for pipe diameters from 22 to 63 mm, 70 mm in length. Maximum working pressure is up to 10 bar.

This type of fitting allows the simultaneous reparation of damaged pipes, and at the same time, obtaining an external connector for the pipe. It can also be used for new installations.

Clamp and outlet are made out of stainless steel (AISI 304 quality), with the TIG-weld with clamp's body. After welding all Stainless Steel parts are passivated to ensure optimal corrosion protection. Tapping clamps can be equipped with a threaded socket or nipple with dimensions of 1/2" to 4".

They are produced as single clamps with a diameter of 60 to 250 mm, and double clamps for the diameters of 88 to 600 mm. Clamp's length may be 100, 150, 200, 250, 300 and 400 mm.

The combination of quality materials and superior design, made that this fitting has a wide application in different kind of industries.

These are an economical alternative for tapped clamps. It is suitable for making connections to valves, T joints, shut-of valves, pipe and conduit fittings, etc. The package ships with a outlet of 1/2" to 3" with a threaded socket or nipple.

Flexible saddle's body allows quick and easy installation. It is produced for pipe diameters from 60 to 600 mm.

It is used for making flanged connections under pressure on the main pipe line, or to repair existing T-connections. Tapping TEE eliminates the need for cutting and wrapping the T-pieces, which allows an inexpensive and quick intervention, without the need to cut off water supply.

It is produced for pipe diameters from DN 80 to DN 800, flanged fitting from DN 50 to DN 200.

Tapping TEE's length can be 300, 400 and 500 mm, or longer, upon customers' requests.

They are used as an additional security of pipe connections.

These are particularly suitable for the compounds, which are exposed to vibrations (e.g., vibrations by traffic), or a landslide.

They are produced for pipes from DN 80 to DN 600.

It is used as a link between the main water supply and internal building plumbing.

The advantage of this collar is that during the assembly period, the water supply network remains under normal pressure.

Mounting can be performed on PVC, steel, asbestos-cement or cast iron pipes with diameters ranging from 63 to 315 mm.

Atlantik flex (repair clamp) is designed for reparation of damaged pipes, as well as pipe connection, where there is an angular deflection from 3° to 5°, or axial deflection between the two pipes up to 3 mm. It is suitable for pipes under pressure, and up to 16 bar.